Data Acquisition Daq System MarketSize, Share & Industry Analysis, 2026-2034By ComponentBy ApplicationBy SpeedBy End-userBy Product Type
Full title & scope — all 5 axes with their segments
Data Acquisition Daq System Market Size, Share & Industry Analysis, By Component (Hardware, Software), By Application (Research & Development, Field, Manufacturing), By Speed (Low Speed, High Speed), By End-user (Aerospace & Defence, Energy & Power, Wireless Communication, Environment Monitoring, Food & Beverage, Healthcare, Automotive & Transportation, Others), By Product Type (Modular DAQ, PC-based (Plug-in Card) DAQ, Standalone/Portable DAQ), and Regional Forecast, 2026-2034
Segment definitions and share of revenue by product, animal, end user and region.
- 01By ComponentHardware · Software
- 02By ApplicationResearch & Development · Field · Manufacturing
- 03By SpeedLow Speed · High Speed
- 04By End-userAerospace & Defence · Energy & Power · Wireless Communication
- 05By Product TypeModular DAQ · PC-based · Standalone/Portable DAQ
- 06By Region
Market Analysis & Outlook
A data acquisition (DAQ) system is the hardware and software combination that captures analogue signals from sensors and instruments, such as voltage, temperature, pressure or vibration, and converts them into digital data a computer or controller can record and analyse. Systems range from modular chassis-based platforms and plug-in cards installed inside a PC to standalone and portable units used away from a fixed lab. Buyers include test and measurement engineers in aerospace, automotive, energy and manufacturing, along with research institutions and environmental or healthcare monitoring programs that need to log physical measurements over time.
USD 2.25 billion of revenue was recorded in the global data acquisition daq system market in 2025. By 2034 the figure reaches USD 4.32 billion, a compound annual growth rate of 7.52% through the forecast period, along a series that runs USD 1.55 billion in 2020, USD 2.1 billion in 2024, USD 2.42 billion in 2026 and USD 3.23 billion in 2030.
Composition changes more than the total does. Software, at 8.96%, outgrows Hardware at 6.83%, and its share moves from 30.2% to 34%. Hardware stays the largest line throughout, at USD 1.57 billion in 2025 and USD 2.85 billion in 2034. The lines gaining share are Software. Hardware lose share without losing revenue.
By application, Research & Development accounts for 45% of 2025 revenue at USD 1.01 billion, reaching USD 1.73 billion and 40% by 2034. Field grows faster at 8.66% against 6.17%, moving from 20% of revenue to 22% by 2034. This axis divides the same revenue as the component split instead of adding to it, so the two are read together and never summed.
The regional order runs from North America at 33% of 2025 revenue down to Latin America at 6%. North America is worth USD 0.74 billion in 2025 and USD 1.3 billion in 2034; Asia Pacific, second at 30%, moves from USD 0.68 billion to USD 1.47 billion. Because Asia Pacific, Latin America and Middle East and Africa take share, the revenue added by 2034 concentrates instead of spreading across all five regions.
Coverage extends to five regions, two component lines and five segmentation axes over the full fifteen years. The 2025 total itself is a triangulation of published figures and category proxies, short of a directly sourced total, and the splits below are estimated on that same basis, a bound on their precision worth carrying into any use of them.
Market Size, 2020–2034
USD BillionRevenue in USD Billion. Values up to 2025 are actuals; 2026–2034 are forecast.
Key Takeaways
- A forecast-period rate of 7.52% takes the market from USD 2.25 billion in 2025 to USD 4.32 billion in 2034, against 7.74% recorded over the 2020-2025 historical period.
- Hardware is the largest component line at USD 1.57 billion in 2025, a 69.8% share, reaching USD 2.85 billion and 66% of revenue by 2034.
- Fastest growth on the component axis belongs to Software: 8.96% a year, USD 0.68 billion to USD 1.47 billion, and a share moving from 30.2% to 34%.
- The bull case puts 2034 revenue at USD 4.88 billion and the bear case at USD 3.72 billion, either side of the USD 4.32 billion base case, each with its own stated assumption in the full report.
- North America holds 33% of global revenue in 2025 at USD 0.74 billion, the largest of the five regions tracked, and reaches USD 1.3 billion by 2034.
- 85.14% of North America's base-year revenue comes from the United States alone: USD 0.63 billion in 2025, rising to USD 1.1 billion by 2034, which is why it is that region's worked example.
- Every line on all five segmentation axes and in each of the five regions carries its own revenue, share and growth rate for all fifteen years, 2020 through 2034, on a 2025 base.
Market Trends
Revenue Share, By By Component
Base year 2025Hardware leads with 69.8% of by component segment revenue.
Share of by component segment revenue, most recent base year.
Three movements define the forecast period in the global data acquisition daq system market: how the component mix changes, where regional weight shifts, and the rate at which the total compounds.
Not one of them points downward. Growth is everywhere in absolute terms, and the interest is entirely in where it lands.
Software grows faster than Hardware. Between 2026 and 2034, 8.96% growth in Software against 6.83% in Hardware pulls the component mix apart. Software takes its share of revenue from 30.2% to 34% while Hardware gives up ground, from 69.8% to 66%. Neither contracts: USD 0.68 billion becomes USD 1.47 billion, USD 1.57 billion becomes USD 2.85 billion. What the spread decides is which of them a supplier's revenue is exposed to.
Regional weight shifts toward Asia Pacific, Latin America and Middle East and Africa. Asia Pacific moves from 30% of revenue in 2025 to 34% in 2034, worth USD 0.68 billion rising to USD 1.47 billion; Latin America moves from 6% of revenue in 2025 to 7% in 2034, worth USD 0.13 billion rising to USD 0.3 billion; Middle East and Africa moves from 7% of revenue in 2025 to 8% in 2034, worth USD 0.16 billion rising to USD 0.34 billion. Against that, North America at 33% moving to 30%, Europe at 24% moving to 21%, a fall in share, not in revenue. Growth is therefore not something a participant inherits from the market; it depends on which regions its revenue is weighted toward.
Growth compounds at 7.52% without a step change. Year by year the total runs USD 1.55 billion in 2020, USD 2.1 billion in 2024, USD 2.25 billion in 2025, USD 2.42 billion in 2026, USD 3.23 billion in 2030 and USD 4.32 billion in 2034. There is no discontinuity to time, and 7.52% forecast growth against 7.74% historical means the trend continues and does not turn. A plan built on this market is therefore a plan about capturing a share of steady expansion, which is decided on the component and regional axes, not by the headline rate.
Market Growth Factors
The fastest line decides the blended rate
Market Drivers
3- 01The fastest line decides the blended rate
At 8.96% against a market rate of 7.52%, Software is the line pulling the average up: USD 0.68 billion to USD 1.47 billion, and 30.2% of revenue to 34%. The market's overall 7.52% depends on that rate holding: at the 6.83% recorded by Hardware, the same revenue base would compound to a materially smaller 2034 total. Exposure to this line, not to the market as a whole, is what determines a supplier's own rate.
- 02The two largest regions hold most of the base
North America is the largest region at USD 0.74 billion in 2025, 33% of global revenue, and reaches USD 1.3 billion by 2034 while holding 30%. Asia Pacific adds a further 30% at USD 0.68 billion, reaching USD 1.47 billion. Together the two account for the majority of both the 2025 base and the revenue added by 2034, which is why a regional plan treating all five regions at equal weight misreads where the growth actually lands.
- 03A demonstrated trajectory, not a projected turnaround
The historical period compounded at 7.74%; USD 1.55 billion in 2020, USD 2.1 billion in 2024 and USD 2.25 billion in 2025. The forecast period then runs at 7.52%, ending 2034 at USD 4.32 billion. Because the growth is already in the record and not only in the projection, the rate is held flat across the forecast instead of ramped, and the risk in the number sits in the mix assumptions, not in whether the market grows at all.
Growth drivers
| # | Growth driver | Impact | Gross contribution (Billion) | 2026-28 | 2029-31 | 2032-34 |
|---|---|---|---|---|---|---|
| 1 | Industry 4.0 and Manufacturing Digitalization | High | +0.62 | High | High | Medium |
| 2 | Electric and Autonomous Vehicle Test Programs | High | +0.52 | Medium | High | High |
| 3 | 5G/6G and Wireless Infrastructure Test Demand | Medium-High | +0.38 | High | Medium | Medium |
| 4 | Renewable Energy and Grid Modernization Monitoring | Medium | +0.3 | Medium | Medium | Medium |
| 5 | Structural Health and Environmental Monitoring Adoption | Medium | +0.22 | Low | Medium | Medium |
| 6 | Others | Low | +0.13 | Low | Low | Low |
| Total | +2.17 | |||||
Restraints
| # | Restraint | Impact | Estimated reduction (Billion) | 2026-28 | 2029-31 | 2032-34 |
|---|---|---|---|---|---|---|
| 1 | Price Competition Compressing Hardware ASPs | Medium | −0.07 | Medium | Medium | High |
| 2 | Extended Replacement Cycles in Mature End Markets | Medium | −0.03 | Low | Medium | Medium |
| Total | −0.1 | |||||
Drivers contribute 2.17 Billion and restraints remove 0.1 Billion, a net 2.07 Billion, which is the revenue the market adds between the base year and 2034. Contributions are CDI estimates, apportioned so that they reconcile with the forecast rather than being read from it.
Separate the 7.52% into its parts and three show up: an already-large base compounding, the component mix moving toward its faster lines, and regional growth landing unevenly.
Restraining Factors
Downside case: USD 3.72 billion by 2034, against USD 4.32 billion in the base case
Market Restraints
2- 01Downside case: USD 3.72 billion by 2034, against USD 4.32 billion in the base case
A bear case of USD 3.72 billion in 2034, against USD 4.32 billion in the base case, rests on one stated assumption: bear case assumes a broader industrial capital spending slowdown than recent history suggests, with manufacturing and vehicle test program budgets growing well below their recent pace for the balance of the forecast period. Neither case changes the USD 2.25 billion 2025 base.
- 02Hardware grows below the market rate
With 69.8% of 2025 revenue (USD 1.57 billion) Hardware is where most of the market sits, and it grows at only 6.83% against the market's 7.52%. Revenue still reaches USD 2.85 billion by 2034 and share still falls to 66%: a drag on the average, not a decline.
Market Opportunities
Upside case: USD 4.88 billion by 2034
Market Opportunities
2- 01Upside case: USD 4.88 billion by 2034
The upside path assumes bull case assumes manufacturing automation capital spending and vehicle electrification test programs expand faster than the base case, with no slowdown in aerospace and defence test budgets through the forecast period. It ends 2034 at USD 4.88 billion against a USD 4.32 billion base case, off the same USD 2.25 billion base year.
- 02The opening is on the component axis, not the regional one
Share on the component axis moves toward Software, from 30.2% in 2025 to 34% in 2034, on 8.96% growth against the market's 7.52% and revenue rising from USD 0.68 billion to USD 1.47 billion. Taking position there does not require displacing whoever holds Hardware, which is the harder and more expensive fight.
Market Challenges
Concentration on the component axis
Market Challenges
2- 01Concentration on the component axis
With 69.8% of 2025 revenue and 66% of 2034 revenue (USD 1.57 billion rising to USD 2.85 billion) Hardware is where the market's exposure sits. Anything that changes demand for it changes the headline number; nothing else on the axis carries that weight.
- 02One country drives the leading region
The United States generates USD 0.63 billion of North America's USD 0.74 billion in 2025, 85.14% of the region, reaching USD 1.1 billion by 2034. Regional totals therefore move largely with one country's demand, so a regional forecast is more exposed to single-country conditions than its size alone suggests.
Segmentation Analysis
5 axesSegmentation runs along five axes: component, application, speed, end-user and product type. They are alternative readings of one revenue pool, not parts that sum to it.
Two component lines are reported. One of them takes share over the forecast period and the other gives it up, though every line grows in absolute terms between 2025 and 2034.
By Component · 2 segments
Scale in Hardware and Growth in Software Define the Component Axis
- Largest Hardware · 69.8%
- Fastest Software · 9%
- Moves most Hardware · -3.8 pts
- Order by 2034 unchanged
| Segment | 2025 | Share | 2034 | Share | CAGR |
|---|---|---|---|---|---|
| Hardware | $1.57B | 69.8% | $2.85B | 66%-3.8 | 6.8% |
| Software | $0.68B | 30.2% | $1.47B | 34%+3.8 | 9% |
Hardware leads because every deployment still needs signal conditioning modules, chassis and sensors before any software license is sold, and replacement cycles on physical instrumentation recur independently of the software layer. Software is the faster grower: buyers are adding analytics, cloud connectivity and remote configuration to systems already installed, without replacing the underlying hardware. Software grows fastest here, so its share rises while Hardware gives ground. By 2034 Hardware is still ahead, making this a shift in weight, not a change of leader. Every year of the series is priced on this axis, making it the reference cut for the rest of the report.
By Application · 3 segments
Research & Development Led by Application in 2025, with Field Growing Fastest
- Largest Research & Development · 45%
- Fastest Field · 8.7%
- Moves most Research & Development · -5 pts
- Order by 2034 unchanged
| Segment | 2025 | Share | 2034 | Share | CAGR |
|---|---|---|---|---|---|
| Research & Development | $1.01B | 45% | $1.73B | 40%-5 | 6.2% |
| Field | $0.45B | 20% | $0.95B | 22%+2 | 8.7% |
| Manufacturing | $0.79B | 35% | $1.64B | 38%+3 | 8.4% |
Research and development leads because university and corporate test labs remain the first adopters of new acquisition capability and evaluate the widest range of instruments per lab. Manufacturing is growing fastest as factories add continuous process and quality monitoring under automation programs, a use case research labs rarely require and field deployments only partly replicate. The order does not change: Research & Development is still largest in 2034, and what moves is how much it holds.
By Speed · 2 segments
Scale in Low Speed (<100 KS/S) and Growth in High Speed (>100 KS/S) Define the Speed Axis
- Largest Low Speed (<100 KS/S) · 57.8%
- Fastest High Speed (>100 KS/S) · 9%
- Moves most Low Speed (<100 KS/S) · -5.7 pts
- Order by 2034 unchanged
| Segment | 2025 | Share | 2034 | Share | CAGR |
|---|---|---|---|---|---|
| Low Speed (<100 KS/S) | $1.30B | 57.8% | $2.25B | 52.1%-5.7 | 6.3% |
| High Speed (>100 KS/S) | $0.95B | 42.2% | $2.07B | 47.9%+5.7 | 9% |
Low speed systems lead because most process monitoring, environmental sensing and general industrial testing never requires capture rates above the entry threshold, and the installed base of such systems is large. High speed systems are growing fastest as demand for RF and microwave testing, vibration analysis and sensor fusion in autonomous systems pushes buyers toward acquisition hardware able to resolve fast transient events. Low Speed (<100 KS/S) remains the largest line through 2034, so the axis changes in proportion, not in order.
By End-user · 8 segments
By End-user
- Largest Aerospace & Defence · 22.2%
- Fastest Environment Monitoring · 10.2%
- Moves most Aerospace & Defence · -2.3 pts
- Order by 2034 unchanged
| Segment | 2025 | Share | 2034 | Share | CAGR |
|---|---|---|---|---|---|
| Aerospace & Defence | $0.50B | 22.2% | $0.86B | 19.9%-2.3 | 6.2% |
| Energy & Power | $0.36B | 16% | $0.65B | 15%-1 | 6.8% |
| Wireless Communication | $0.27B | 12% | $0.56B | 13%+1 | 8.4% |
| Environment Monitoring | $0.18B | 8% | $0.43B | 10%+2 | 10.2% |
| Food & Beverage | $0.16B | 7.1% | $0.26B | 6%-1.1 | 5.5% |
| Healthcare | $0.22B | 9.8% | $0.48B | 11.1%+1.3 | 9.1% |
| Automotive & Transportation | $0.40B | 17.8% | $0.86B | 19.9%+2.1 | 8.9% |
| Others | $0.16B | 7.1% | $0.22B | 5.1%-2 | 3.6% |
2025 to 2034 revenue and share by line: Aerospace & Defence USD 0.5 billion to USD 0.86 billion (22.2% to 19.9%), Automotive & Transportation USD 0.4 billion to USD 0.86 billion (17.8% to 19.9%), Energy & Power USD 0.36 billion to USD 0.65 billion (16% to 15%), Wireless Communication USD 0.27 billion to USD 0.56 billion (12% to 13%), Healthcare USD 0.22 billion to USD 0.48 billion (9.8% to 11.1%), Environment Monitoring USD 0.18 billion to USD 0.43 billion (8% to 10%), Food & Beverage USD 0.16 billion to USD 0.26 billion (7.1% to 6%), Others USD 0.16 billion to USD 0.22 billion (7.1% to 5.1%). Scale in Aerospace & Defence and Growth in Environment Monitoring Define the End-user Axis Aerospace and defence leads because flight test, propulsion validation and structural qualification programs each require dense multi-channel acquisition across long test campaigns, a scale few other buyers match. Automotive and transportation is growing fastest as electrification and autonomous-driving validation add categories of sensor testing that combustion-era programs never needed. By 2034 Aerospace & Defence is still ahead, making this a shift in weight, not a change of leader.
By Product Type · 3 segments
Modular DAQ Holds the Largest Product type Share and Is Still the Quickest to Grow
- Largest Modular DAQ · 48%
- Fastest Modular DAQ · 8.5%
- Moves most PC-based (Plug-in Card) DAQ · -5.7 pts
- Order by 2034 unchanged
| Segment | 2025 | Share | 2034 | Share | CAGR |
|---|---|---|---|---|---|
| Modular DAQ | $1.08B | 48% | $2.25B | 52.1%+4.1 | 8.5% |
| PC-based (Plug-in Card) DAQ | $0.67B | 29.8% | $1.04B | 24.1%-5.7 | 5% |
| Standalone/Portable DAQ | $0.50B | 22.2% | $1.03B | 23.8%+1.6 | 8.4% |
Modular systems lead because their channel count and instrument mix can be reconfigured for a new test program without replacing the chassis, suiting labs running many different campaigns on the same capital equipment. Standalone and portable systems are growing fastest as field, in-vehicle and structural-health monitoring applications move acquisition capability outside the lab. Modular DAQ remains the largest line through 2034, so the axis changes in proportion, not in order.
Regional Insights
Regional Revenue Share
Base year 2025Share of global revenue in the base year.
Only the leading region's share is published outside the report; pins mark the region, not a specific country.
North America Market Analysis
The largest region covered — 2.9 points of share move elsewhere by 2034, while revenue still grows 1.8×.
- Rank 1 of 5
- 2025 share 33%
- By 2034 30.1%
- Revenue $0.74B → $1.30B
USD 0.74 billion of 2025 revenue is generated in North America, 33% of the global data acquisition daq system market with USD 1.3 billion projected for 2034. That makes it the first-largest region covered, in 2025 and again in 2034.
Its share moves to 30% by 2034, though revenue still rises throughout; the shift is in the region's weight against faster-growing ones, which is not the same as weakening demand.
Hardware leads here as it does globally, at 69.8% of 2025 revenue, and Software again grows fastest at 8.96%. Revenue for North America is broken out by every segmentation axis and by country in the full report.
United States
Sets the pace for North America at 85.1% of it, growing 1.7×.
- In region 1 of 2
- Of region 85.1%
- Of global 28%
- Revenue $0.63B → $1.10B
The United States is the largest market within North America, generating USD 0.63 billion in 2025 and projected to reach USD 1.1 billion by 2034. 85.14% of the region in 2025 means the regional figures are, in practice, a view of this market with others attached. Against regional totals of USD 0.74 billion in 2025 and USD 1.3 billion in 2034, it is the country the full report breaks out in detail.
The component pattern in the United States is the global one: 69.8% of 2025 revenue in Hardware, 66% by 2034, against 8.96% growth in Software taking it from 30.2% to 34%. Its 85.14% weight in North America means those movements carry straight into the regional totals. Revenue by component for the United States is reported separately in the full report.
Data acquisition hardware sold in the United States falls under the Federal Communications Commission's rules for unintentional radiators, since these instruments generate and process electronic signals that could interfere with other equipment. A supplier must test emissions against the applicable FCC part and declare conformity before importing or marketing the system. Electrical safety is addressed separately through certification by a nationally recognized testing laboratory such as UL, confirming the device meets recognized safety standards for measurement and control equipment. Where a system incorporates wireless data transfer, additional equipment authorization applies. Federal procurement buyers may also require compliance with cybersecurity and supply-chain provisions before a DAQ system can be deployed on government networks. No premarket approval regime comparable to medical devices applies to this category.
The suppliers tracked in this study (Advantech Co. Ltd., National Instruments Corporation, Schneider Electric SE, ABB Ltd, Honeywell International, Siemens AG, Rockwell Automation Inc., Keysight Technologies, General Electric Ltd., Omron Corporation, Yokogawa Electric Co., Tektronix, AMETEK (VTI Instruments) and Bustec) compete in the United States across the component lines above. Two different problems sit on the same axis: holding Hardware at 69.8% of 2025 revenue, and taking Software while it grows at 8.96%. The full report covers country-level positioning and shares company by company; this summary does not.
Canada
2nd-largest in North America, growing 1.8×.
- In region 2 of 2
- Of region 13.5%
- Of global 4.4%
- Revenue $0.10B → $0.18B
4.44% of global revenue is generated in Canada; USD 0.1 billion in 2025, reaching USD 0.18 billion in 2034, and 13.51% of North America.
Europe Market Analysis
The 3rd-largest region covered — 2.9 points of share move elsewhere by 2034, while revenue still grows 1.7×.
- Rank 3 of 5
- 2025 share 24%
- By 2034 21.1%
- Revenue $0.54B → $0.91B
24% of the global data acquisition daq system market sits in Europe in 2025, worth USD 0.54 billion with USD 0.91 billion projected for 2034. Among the five regions it ranks third by revenue in both years.
21% of global revenue sits here in 2034, below the 2025 level, while nothing contracts here; other regions simply grow faster, which shows up as relative weight, not as falling revenue.
Segment composition follows the global pattern: Hardware largest at 69.8% of 2025 revenue, Software fastest at 8.96%. Europe is reported axis by axis and country by country in the full study.
Germany
The largest market in Europe, growing 1.6×.
- In region 1 of 3
- Of region 35.2%
- Of global 8.4%
- Revenue $0.19B → $0.31B
Germany is the largest market within Europe, generating USD 0.19 billion in 2025 and projected to reach USD 0.31 billion by 2034. At 35.19% of the region in 2025 it leads, but a majority of Europe's revenue is generated in other markets. Set against USD 0.54 billion and USD 0.91 billion for the region, it is why this market, and not a smaller one, is the one reported in full.
Composition here matches the global split: the largest line is Hardware at 69.8% of 2025 revenue, easing to 66% by 2034, and the fastest is Software at 8.96%, from 30.2% to 34%. With 35.19% of Europe concentrated here, a change in this country's mix is visible in the regional figures instead of being diluted by its neighbours. Germany carries its own component breakdown in the full report.
In Germany, data acquisition systems fall under European Union law governing electrical and electronic equipment, applied domestically through the Federal Network Agency and national market surveillance authorities. A manufacturer must self-declare conformity with the EU Electromagnetic Compatibility Directive and the EU Low Voltage Directive, affix the CE mark, and keep supporting technical documentation available for inspection. The EU RoHS Directive restricts hazardous substances used in the equipment's construction, and the EU WEEE Directive governs its eventual collection and recycling. If a unit incorporates wireless communication modules, radio equipment rules add a further conformity step and, in some cases, notified-body involvement. Standards conformity is typically demonstrated against harmonized European norms for measurement, control, and laboratory equipment.
Competition in Germany runs between the suppliers this study tracks: Advantech Co. Ltd., National Instruments Corporation, Schneider Electric SE, ABB Ltd, Honeywell International, Siemens AG, Rockwell Automation Inc., Keysight Technologies, General Electric Ltd., Omron Corporation, Yokogawa Electric Co., Tektronix, AMETEK (VTI Instruments) and Bustec. Volume sits in Hardware at 69.8% of 2025 revenue; movement sits in Software at 8.96% growth. Weighting toward Europe means competing for 24% of 2025 global revenue, a base of USD 0.54 billion moving to USD 0.91 billion across the forecast period.
United Kingdom
2nd-largest in Europe, growing 1.6×.
- In region 2 of 3
- Of region 24.1%
- Of global 5.8%
- Revenue $0.13B → $0.21B
The United Kingdom is sized at USD 0.13 billion in 2025, rising to USD 0.21 billion by 2034; 5.78% of global revenue and 24.07% of Europe. It is reported separately from Germany across every segmentation axis in the full report.
France
3rd-largest in Europe, growing 1.7×.
- In region 3 of 3
- Of region 16.7%
- Of global 4%
- Revenue $0.09B → $0.15B
France is sized at USD 0.09 billion in 2025, rising to USD 0.15 billion by 2034; 4% of global revenue and 16.67% of Europe. It is reported separately from Germany across every segmentation axis in the full report.
Asia Pacific Market Analysis
The 2nd-largest region covered, and the one gaining the most — it picks up 4 points of share by 2034, while revenue still grows 2.2×.
- Rank 2 of 5
- 2025 share 30%
- By 2034 34%
- Revenue $0.68B → $1.47B
30% of the global data acquisition daq system market sits in Asia Pacific in 2025, worth USD 0.68 billion with USD 1.47 billion projected for 2034. Among the five regions it ranks second by revenue in both years.
Its share rises to 34% over the forecast period, because it outgrows the market's 7.52%; the revenue added here is disproportionate to where the region started.
Hardware leads here as it does globally, at 69.8% of 2025 revenue, and Software again grows fastest at 8.96%. Asia Pacific is reported axis by axis and country by country in the full study.
China
The largest market in Asia Pacific, growing 2.1×.
- In region 1 of 3
- Of region 41.2%
- Of global 12.4%
- Revenue $0.28B → $0.58B
USD 0.28 billion of Asia Pacific's 2025 revenue is generated in China, the region's largest market, reaching USD 0.58 billion by 2034. At 41.18% of the region in 2025 it leads, but a majority of Asia Pacific's revenue is generated in other markets. Set against USD 0.68 billion and USD 1.47 billion for the region, it is why this market, and not a smaller one, is the one reported in full.
Demand in China follows the component mix reported at global level: Hardware is the largest line at 69.8% of 2025 revenue, moving to 66% by 2034, while Software grows fastest at 8.96% and takes its share from 30.2% to 34%. Since 41.18% of Asia Pacific's revenue is generated here, the regional numbers inherit this market's mix instead of smoothing it out. Revenue by component for China is reported separately in the full report.
In China, data acquisition equipment is regulated as an electronic product under the compulsory certification system administered by the State Administration for Market Regulation and the Certification and Accreditation Administration. Depending on its function, a unit may need the China Compulsory Certification mark before it can be imported, sold, or used commercially, along with testing against relevant national GB standards for electrical safety and electromagnetic compatibility. A system with wireless or radio-frequency components additionally requires type approval from the radio regulatory authority before it can be marketed within the country. Importers must retain test reports and factory inspection records to support ongoing compliance, and customs authorities may request these documents at the point of entry.
Competition in China runs between the suppliers this study tracks: Advantech Co. Ltd., National Instruments Corporation, Schneider Electric SE, ABB Ltd, Honeywell International, Siemens AG, Rockwell Automation Inc., Keysight Technologies, General Electric Ltd., Omron Corporation, Yokogawa Electric Co., Tektronix, AMETEK (VTI Instruments) and Bustec. Two different problems sit on the same axis: holding Hardware at 69.8% of 2025 revenue, and taking Software while it grows at 8.96%. A supplier weighted toward Asia Pacific is competing over a base of USD 0.68 billion in 2025 reaching USD 1.47 billion by 2034, 30% of global revenue at the start of that period.
Japan
2nd-largest in Asia Pacific, growing 1.8×.
- In region 2 of 3
- Of region 23.5%
- Of global 7.1%
- Revenue $0.16B → $0.29B
Within Asia Pacific, Japan accounts for 23.53% of regional revenue and 7.11% of the global total, worth USD 0.16 billion in 2025 and USD 0.29 billion by 2034.
India
3rd-largest in Asia Pacific, growing 2.7×.
- In region 3 of 3
- Of region 13.2%
- Of global 4%
- Revenue $0.09B → $0.24B
4% of global revenue is generated in India; USD 0.09 billion in 2025, reaching USD 0.24 billion in 2034, and 13.24% of Asia Pacific.
Latin America Market Analysis
The 5th-largest region covered — it picks up 0.9 points of share by 2034, while revenue still grows 2.3×.
- Rank 5 of 5
- 2025 share 6%
- By 2034 6.9%
- Revenue $0.13B → $0.30B
Latin America holds 6% of the global data acquisition daq system market in 2025, worth USD 0.13 billion rising to USD 0.3 billion in 2034. It is a marginal region on this axis, fifth by revenue throughout the period.
By 2034 the share has moved up to 7%, on growth above the market's own 7.52%, and with a bigger contribution to the revenue added over the period than the base-year figure suggests.
Hardware leads here as it does globally, at 69.8% of 2025 revenue, and Software again grows fastest at 8.96%. Per-axis and per-country detail for Latin America sits in the full report.
Brazil
The largest market in Latin America, growing 2.3×.
- In region 1 of 2
- Of region 53.9%
- Of global 3.1%
- Revenue $0.07B → $0.16B
USD 0.07 billion of Latin America's 2025 revenue is generated in Brazil, the region's largest market, reaching USD 0.16 billion by 2034. It accounts for 53.85% of regional revenue in the base year, the largest single share without dominating the region outright. Regional revenue of USD 0.13 billion in 2025 and USD 0.3 billion in 2034 sits around it, and it is the country used wherever the full report cuts a figure by geography.
Composition here matches the global split: the largest line is Hardware at 69.8% of 2025 revenue, easing to 66% by 2034, and the fastest is Software at 8.96%, from 30.2% to 34%. Its 53.85% weight in Latin America means those movements carry straight into the regional totals. Per-component revenue for Brazil appears on its own in the full report.
In Brazil, data acquisition instruments are subject to conformity assessment overseen by the National Institute of Metrology, Quality and Technology, which sets requirements for electrical safety and electromagnetic compatibility on equipment of this kind. Suppliers typically obtain certification through an accredited body and apply the required conformity mark before the product can be sold domestically. Where a system includes wireless connectivity, separate homologation from the National Telecommunications Agency is required, covering radio-frequency performance and interference limits. Imported units must also satisfy customs and labelling rules that identify the manufacturer, the importer of record, and the product's intended use, and technical files must remain available to regulators on request.
Competition in Brazil runs between the suppliers this study tracks: Advantech Co. Ltd., National Instruments Corporation, Schneider Electric SE, ABB Ltd, Honeywell International, Siemens AG, Rockwell Automation Inc., Keysight Technologies, General Electric Ltd., Omron Corporation, Yokogawa Electric Co., Tektronix, AMETEK (VTI Instruments) and Bustec. The commercially relevant division is 69.8% of 2025 revenue in Hardware, where the volume is, against 8.96% growth in Software, where share moves. Weighting toward Latin America means competing for 6% of 2025 global revenue, a base of USD 0.13 billion moving to USD 0.3 billion across the forecast period.
Mexico
2nd-largest in Latin America, growing 2.3×.
- In region 2 of 2
- Of region 30.8%
- Of global 1.8%
- Revenue $0.04B → $0.09B
1.78% of global revenue is generated in Mexico; USD 0.04 billion in 2025, reaching USD 0.09 billion in 2034, and 30.77% of Latin America.
Middle East and Africa Market Analysis
The 4th-largest region covered — it picks up 0.9 points of share by 2034, while revenue still grows 2.1×.
- Rank 4 of 5
- 2025 share 7%
- By 2034 7.9%
- Revenue $0.16B → $0.34B
Middle East and Africa holds 7% of the global data acquisition daq system market in 2025, worth USD 0.16 billion and reaches USD 0.34 billion by 2034. It is a marginal region on this axis, fourth by revenue throughout the period.
Share climbs to 8% by 2034, so the region grows faster than the market's 7.52% and takes a larger part of the revenue added by 2034 than its 2025 weight implies.
The component mix reported at global level applies here, with Hardware the largest line at 69.8% of 2025 revenue and Software the fastest-growing at 8.96%. Per-axis and per-country detail for Middle East and Africa sits in the full report.
Saudi Arabia
The largest market in Middle East and Africa, growing 2.2×.
- In region 1 of 2
- Of region 37.5%
- Of global 2.7%
- Revenue $0.06B → $0.13B
Saudi Arabia is the largest market within Middle East and Africa, generating USD 0.06 billion in 2025 and projected to reach USD 0.13 billion by 2034. At 37.5% of the region in 2025 it leads, but a majority of Middle East and Africa's revenue is generated in other markets. Against regional totals of USD 0.16 billion in 2025 and USD 0.34 billion in 2034, it is the country the full report breaks out in detail.
Demand in Saudi Arabia follows the component mix reported at global level: Hardware is the largest line at 69.8% of 2025 revenue, moving to 66% by 2034, while Software grows fastest at 8.96% and takes its share from 30.2% to 34%. With 37.5% of Middle East and Africa concentrated here, a change in this country's mix is visible in the regional figures instead of being diluted by its neighbours. Revenue by component for Saudi Arabia is reported separately in the full report.
In Saudi Arabia, data acquisition systems fall under the conformity assessment programme run by the Saudi Standards, Metrology and Quality Organization, which requires suppliers to register the product and obtain a certificate of conformity before shipment, processed through the kingdom's electronic conformity platform. The certificate confirms conformity with applicable safety and electromagnetic compatibility standards adopted from recognized international frameworks. Equipment that transmits or receives radio signals also needs type approval from the Communications, Space and Technology Commission before it can be imported or operated. Distributors must ensure that packaging and documentation carry the required conformity mark and accurate technical labelling, and customs clearance depends on this certification being in place beforehand.
In Saudi Arabia the field is Advantech Co. Ltd., National Instruments Corporation, Schneider Electric SE, ABB Ltd, Honeywell International, Siemens AG, Rockwell Automation Inc., Keysight Technologies, General Electric Ltd., Omron Corporation, Yokogawa Electric Co., Tektronix, AMETEK (VTI Instruments) and Bustec. The commercially relevant division is 69.8% of 2025 revenue in Hardware, where the volume is, against 8.96% growth in Software, where share moves. The commercial size of that position is USD 0.16 billion in 2025 and USD 0.34 billion by 2034, 7% of the global total in the base year.
United Arab Emirates
2nd-largest in Middle East and Africa, growing 2.3×.
- In region 2 of 2
- Of region 25%
- Of global 1.8%
- Revenue $0.04B → $0.09B
1.78% of global revenue is generated in the United Arab Emirates; USD 0.04 billion in 2025, reaching USD 0.09 billion in 2034, and 25% of Middle East and Africa.
Request this sample to see the full data tables and segment-level detail behind this analysis.
Report Coverage
This report assesses the market across every segment, with revenue and a growth rate for each line in each year of the study period. It covers the drivers, trends, opportunities, restraints and challenges shaping growth, the competitive landscape and the companies profiled, and the research methodology behind every estimate. Segmentation is reported by Component, Application, Speed, End-User, Product Type, and regional analysis covers North America, Europe, Asia Pacific, Latin America, Middle East and Africa, each broken out by country.
Competitive Landscape
Suppliers Compete on Hardware Volume and Software Momentum
The field covered here is Advantech Co. Ltd., National Instruments Corporation, Schneider Electric SE, ABB Ltd, Honeywell International, Siemens AG, Rockwell Automation Inc., Keysight Technologies, General Electric Ltd., Omron Corporation, Yokogawa Electric Co., Tektronix, AMETEK (VTI Instruments) and Bustec.
Where suppliers actually compete is along the component axis. Hardware is 69.8% of 2025 revenue at USD 1.57 billion and still 66% in 2034, so it is where the volume sits and where an incumbent's position is hardest to move. Software, compounding at 8.96% against 6.83% for Hardware, is where share changes hands over the forecast period. Holding the first and taking the second are separate capabilities, which is why a market of USD 2.25 billion supports as many suppliers as it does.
Scale in calibration and manufacturing separates the largest suppliers, letting them support the channel counts and accuracy specifications that aerospace, defence and automotive test programs require. A broad software and driver ecosystem matters as much as the hardware itself, since buyers standardize on a platform for years and switching cost rises with every added instrument. Industrial automation incumbents extend from an installed base in adjacent control and instrumentation lines, giving them channel reach smaller specialists lack. Regional and niche suppliers compete on application-specific engineering support, faster lead times and price in segments the larger platform vendors treat as secondary.
Geographic reach is the other axis of competition. North America alone accounts for 33% of 2025 revenue, so a supplier absent there is absent from the largest part of the market whatever its position elsewhere; Asia Pacific adds a further 30%.
Per-company profiles, financials, share and development history are in the full report and not here.
List of Key Data Acquisition Daq System Market Companies Profiled
14 companies profiled. Company profiles, including financials, product portfolios and recent developments, are part of the full report.
- Advantech Co. Ltd.(Taiwan)
- National Instruments Corporation(United States)
- Schneider Electric SE(France)
- ABB Ltd(Switzerland)
- Honeywell International(United States)
- Siemens AG(Germany)
- Rockwell Automation Inc.(United States)
- Keysight Technologies(United States)
- General Electric Ltd.(United States)
- Omron Corporation(Japan)
- Yokogawa Electric Co.(Japan)
- Tektronix(United States)
- AMETEK (VTI Instruments)(United States)
- Bustec(Ireland)
Geographic Coverage
Every market below is broken out separately in the report.
North America
3Europe
8Asia Pacific
12Latin America
3Middle East and Africa
4Key Insights
Report Scope
Study parameters & segmentationThis study covers market size and forecasts over the 2020–2034 period, segmentation across 5 axes (Component, Application, Speed, End-user, Product Type), regional analysis for 5 regions and their constituent countries, a competitive landscape profiling 14 key companies, and the research methodology behind every estimate.
Segmentation
5 axes + regionFull chapter-and-section structure of the report. Segment, region, and company breakdowns are listed as scope. The underlying figures are in the sample and full report.
Table of Contents+−
Chapter 1.Executive Summary
Chapter 2.Premium Insights
Chapter 3.Market Definition
Chapter 4.Research Methodology
Chapter 5.Strategic Imperatives & Market Outlook
Chapter 6.Go-to-Market (GTM) Strategies
Chapter 7.Market Trends, Strategy & Dynamics
Chapter 8.Porter's Five Forces
Chapter 9.PESTEL Analysis
Chapter 10.Value Chain Analysis
Chapter 11.Supply Chain Analysis
Chapter 12.Macro-Economic Factors
Chapter 13.Market Cost Analysis
Chapter 14.Market Supply-Side Analysis
Chapter 15.Global Data Acquisition Daq System Market Size & Projections, 2020–2034, Revenue (USD Billion)
Chapter 16.Global Data Acquisition Daq System Market Overview, By Component, 2020–2034, Revenue (USD Billion)
Chapter 17.Global Data Acquisition Daq System Market Overview, By Application, 2020–2034, Revenue (USD Billion)
Chapter 18.Global Data Acquisition Daq System Market Overview, By Speed, 2020–2034, Revenue (USD Billion)
Chapter 19.Global Data Acquisition Daq System Market Overview, By End-user, 2020–2034, Revenue (USD Billion)
Chapter 20.Global Data Acquisition Daq System Market Overview, By Product Type, 2020–2034, Revenue (USD Billion)
Chapter 21.Global Data Acquisition Daq System Market Size — Segment Comparison
Chapter 22.Global Data Acquisition Daq System Geography Overview, 2020–2034, Revenue (USD Billion)
Chapter 23.North America Data Acquisition Daq System Market Deep-Dive, 2020–2034, Revenue (USD Billion)
Chapter 24.Europe Data Acquisition Daq System Market Deep-Dive, 2020–2034, Revenue (USD Billion)
Chapter 25.Asia Pacific Data Acquisition Daq System Market Deep-Dive, 2020–2034, Revenue (USD Billion)
Chapter 26.Latin America Data Acquisition Daq System Market Deep-Dive, 2020–2034, Revenue (USD Billion)
Chapter 27.Middle East and Africa Data Acquisition Daq System Market Deep-Dive, 2020–2034, Revenue (USD Billion)
Chapter 28.Application / Use-Case Analysis
Chapter 29.Vendor Capability Scorecard
Chapter 30.Scenario Forecasts
Chapter 31.Top 10 Key Clients of Top 10 Players
Chapter 32.Top 10 Suppliers
Chapter 33.Competitive Landscape
Chapter 34.Partnerships & M&A
Chapter 35.Key Vendor Analysis
Chapter 36.Marketing Strategy Analysis, Distributors & Traders
Chapter 37.Outlook of the Market
Chapter 38.Concluding Analyst Note
List of Figures+−
Structural index generated from this report's own section headings, not verified against the delivered report's actual figure numbering.
List of Tables+−
Structural index generated from this report's own section headings, not verified against the delivered report's actual table numbering.
Segmentation Analysis
5 axesBy Component
2- 01Hardware
- 02Software
By Application
3- 01Research & Development
- 02Field
- 03Manufacturing
By Speed
2- 01Low Speed (<100 KS/S)
- 02High Speed (>100 KS/S)
By End-user
8- 01Aerospace & Defence
- 02Energy & Power
- 03Wireless Communication
- 04Environment Monitoring
- 05Food & Beverage
- 06Healthcare
- 07Automotive & Transportation
- 08Others
By Product Type
3- 01Modular DAQ
- 02PC-based (Plug-in Card) DAQ
- 03Standalone/Portable DAQ
Segment categories shown for scope reference. See the Summary tab for revenue share by By Component. Full segment-by-segment detail across every axis is available in the sample and full report.
Research approach
A market size is a claim about the world, and a claim is only as good as the route to it. Every study is built upward from units and prices — what is actually produced, sold or performed, at what it actually changes hands for — rather than from a headline figure divided downwards. Disclosed company revenue is then used to check that build, not to produce it.
Sizing starts from unit volumes: shipments of DAQ hardware modules, chassis and plug-in cards tracked against realised average selling prices by product type and channel count, split between low-speed and high-speed acquisition rates. Software attach is built separately from license and subscription counts per installed hardware unit. This bottom-up build is checked against disclosed revenue from the major listed suppliers named in this report, weighted by their known share of test-and-measurement or industrial-automation segment revenue. Where the two diverge, for example when a supplier's disclosed segment growth outpaces the unit-volume build, the correction is made to the underlying volume or price assumption feeding the bottom-up model, not by averaging the two figures together.
The four stages
The same sequence runs behind every published study, whatever the industry. The order matters as much as the steps: the segment axes are fixed before any number is collected, so the model is never reshaped to fit whatever data happens to turn up.
What the build rests on, and what checks it
The two are not interchangeable. The left column produces the number; the right column tests it. When the check disagrees with the build, the answer is to find which bottom-up assumption is wrong — a unit count, a price, a take-up rate — not to split the difference between them.
- Volume actually transacted — units produced, installed, dispensed or procedures performed, counted at the level each is genuinely recorded
- Realised pricing by tier and channel, rather than one blended average applied across the whole market
- Take-up and frequency: how much of the addressable base buys, and how often it repeats
- Disclosed revenue of the companies serving the market, where filings separate it far enough to be usable
- Buyer-side spending totals — capital budgets, procurement lines, or the output of the end market the product is bought against
- Trade and customs flows, where the product crosses borders in a separately recorded form
Data sources
Published data establishes what happened. Only the people transacting in a market can say why, and what is about to change — so the two are collected separately and weighted differently.
- Commercial and product leadership at the companies that supply the market
- Procurement and specification leads at the organisations that buy it
- Distributors, integrators and channel partners, where the market is served indirectly
- Regulatory and standards specialists, where approval governs what can be sold at all
- Company filings, annual reports and investor disclosure
- Government statistics, customs records and regulatory registers
- Trade association output and standards-body publications
- Technical and peer-reviewed literature, where the market rests on a clinical or engineering claim
Interviews target procurement and test-engineering managers at aerospace, automotive and industrial manufacturers who specify and buy acquisition hardware, along with product managers and channel heads at the instrument suppliers themselves. Regulatory and standards-body contacts are included where calibration or certification requirements shape purchase timing, particularly in aerospace and healthcare test applications. Distribution and systems-integrator contacts add visibility into deals that never reach the manufacturer directly. Sampling emphasises North America and East Asia, where the largest concentration of both instrument suppliers and heavy industrial test buyers sit, with additional coverage in Western Europe for aerospace and automotive test programs headquartered there.
Desk research draws on customs and trade classification data under HS code 9030 for test and measurement instruments, national manufacturing output statistics for the industrial end markets that buy this equipment, and public filings from the listed suppliers named in this report for segment revenue and channel commentary. Aerospace and defence procurement notices and calibration accreditation registers inform demand timing in that end-use segment. Trade-association benchmarks from instrumentation and automation industry bodies are used to cross-check regional shipment patterns where company-level disclosure does not break out acquisition hardware separately from a supplier's broader test-and-measurement portfolio.
Desk research runs across proprietary research databases including Factiva, OneSource and Hoovers alongside the public sources above. Modelling and statistical validation are run in SAS and SPSS.
Forecasting
The forecast is not a growth rate applied to a base year. It is built from the drivers that are expected to change, each one stated so a reader can disagree with it.
The forecast is built from expected growth in the end markets that drive acquisition hardware demand: manufacturing automation capital spending, aerospace and defence test program budgets, and vehicle electrification test programs, each carrying its own adoption curve instead of one blended growth rate applied across the market. Pricing is held roughly flat in real terms for mature product types and assumed to decline gradually for entry-level modules as competition increases. The 2020-2021 disruption to industrial capital spending is treated as an anomaly and normalised out of the base trend. The forecast holds if manufacturing capital spending and vehicle test budgets continue their current expansion path without a broader industrial recession.
Triangulation and validation
No figure enters a report on the strength of one source. Where the two sizing routes disagree the difference is not averaged away — the assumption causing it is isolated, tested against a third independent measure, and either corrected or carried forward as a stated limitation. Historical years are back-tested against the growth actually recorded before any forecast is allowed to run forward from them.
Outputs are back-tested against recorded shipment and revenue growth for the 2020-2024 period to confirm the model reproduces known historical patterns before it is extended forward. Segment share shifts, including the move toward modular product types and high-speed acquisition rates, are reviewed against supplier product-line announcements and channel feedback, not accepted from the volume model alone. Sensitivities are run on the two assumptions the forecast is most exposed to: manufacturing capital spending growth and the pace of vehicle electrification test adoption. Regional splits are checked against each country's own industrial output and aerospace or automotive program activity to confirm no single country's contribution is overstated relative to its underlying industrial base.
Confidence and limitations
Where an estimate is firm and where it is not is stated rather than left to be inferred from the precision of the number.
Confidence is firmest in the component and application splits, where supplier product-line disclosure and end-market capital spending data are both current and detailed. It is weaker in the end-user breakdown for environment monitoring and food and beverage, where acquisition hardware is often bundled into a larger automation purchase and reported at that level, not separately. Regional figures for the Middle East and Africa and Latin America rest on thinner disclosure than North America, Europe or East Asia. A slowdown in industrial capital spending broader than the historical cycles used for back-testing would be the main structural risk to this forecast.
Every report purchase includes direct access to the lead analyst for scoping questions on the data, at no extra cost and with no separate booking process.
Request a tailored breakdown by geography, segment, or competitor set beyond what's in the standard report.
Questions This Report Answers
6 questionsWhat is the market size and growth rate, globally and by region?
How is the market segmented, and which segments lead?
Which regions and countries are covered, and how do they compare?
What are the key drivers, restraints, opportunities and challenges?
Who are the leading companies operating in this market?
What trends are expected to shape the market through the forecast period?
Frequently Asked Questions
01What is the Data Acquisition Daq System Market projected to reach?
USD 4.32 Billion by 2034, CAGR 7.52%
02What years does this report cover?
Study period 2020–2034, base year 2025, historical data 2020-2024, forecast period 2026-2034.
03Which regions are covered?
North America, Europe, Asia Pacific, Latin America, Middle East and Africa.
04Which region accounted for the largest market share?
North America leads with 33% of global revenue through 2034.
05Which segment leads the market?
Hardware is the largest line by Component, at 69.8% of revenue in 2025.
06Who are the key companies profiled?
Advantech Co. Ltd., National Instruments Corporation, Schneider Electric SE, ABB Ltd, Honeywell International, Siemens AG, Rockwell Automation Inc., Keysight Technologies, General Electric Ltd., Omron Corporation, Yokogawa Electric Co., Tektronix, AMETEK (VTI Instruments), Bustec. Full profiles are part of the paid report.
07Can the segmentation be customized?
Yes. Custom data cuts by geography, segment, or competitor set are available on request.
Why choose CDI
Need this report shaped around your question?
The scope isn't fixed. Tell us what your team needs that the standard edition doesn't cover, and an analyst will come back on what can be adjusted and how long it takes, before you commit to anything.
Most licences include 30–60 hours of customization at no extra cost. See what each licence includes
Additional Companies
Add competitors, suppliers or the peer set you benchmark against to the companies already covered.
Deeper Competitive View
Sharpen the landscape work around your own position: product line, channel, or a named shortlist of rivals.
Extra Segment Splits
Break the market down along an axis the standard scope doesn't cut it by, or go a level deeper inside one.
Application Focus
Narrow the analysis to the specific use cases and end users your team actually sells into.
Different Time Frame
Move the base year, or widen the historical and forecast windows the study is built on.
Country-Level Detail
Go below region level into the individual countries that matter to you, rather than the standard geography split.